Order

Vintage & Classic Tube Guitar Amplifier

Four in one:

Analog amplifier made in Master Tube Design technologii.

The amplifier is equipped with a 4-way power output selector. It allows you to use speaker cabinets of any size, power and impedance.

The following power options are available:

12W, 20W, 40W and 90Wat

The amplifier automatically adjusts its operating parameters and can serve 4, 8 and 16 Ohm cabinets.

If you want to record your guitar or use the amplifier as a pre-amp without a cabinet then you have a special tool on board, an advanced loudspeaker simulator.

Signal from Line-out can be lead in different ways: with simulation, without simulation or both.

You can choose accurate simulations of two types of speakers:
Celestion Vintage-30 and Celestion Creamback.

A simulation of the microphone position is also available and provides additional possibilities of equalizing the colour of your sound at the line output.

Thanks to this solution you can get closer to the sound conditions of a classic set of speakers with a microphone setup. You get the right placement and sound of the instrument in the band's mix by transmitting the signal from the line output without using the speaker.

5-footswitches to access for the following options:

Clean, Crunch, Drive, Boost, Reverb

Additional outputs for external controller.

Foot Controller

Clean, Crunch, Drive, Boost and Reverb.

Cabinet Simulator

2-types of speakers: Celestion Vintage-30 and Celestion Creamback.
Adjustment for microphone position.

Preamp

You can use Stomp-Head as a preamp without connection to cabinet.

Amplifier

This compact amp delivers enough loudness level for any stage size.

Basket

Buy now

Order now

Specification:

Power stage efficiency: 200Watt
Power output selector: 90W, 40W, 20W, 12W
Speakers impedance auto detection: 4,8 and 16ohm
Tubes: 12AX7
2 channels: CLEAN+CRUNCH and LEAD
5 footswitches: CLEAN, CRUNCH, DRIVE, REVERB, BOOST

CONTROLS:
BASS, MIDDLE, TREBLE, PRESENCE, CRUNCH + VOLUME, DRIVE + VOLUME, BOOST, REVERB
Input GAIN boost (switch +6dB)
MUTE
RESONANCE – switch increasing the sound in the resonance range of the loudspeaker
Serial EFFECT LOOP
LINE OUTPUT with Speaker Simulation. Allows send linear signal with simulation (PIN) or without simulation (RING) or both simultaneously
EXTERNAL CONTROLLER INPUT for channel selector and BOOST
Voltage selector 230V/50Hz or 115V/60Hz
Dimensions: (H x W x D) 90 x 330 x 205 mm
Weight: 2,45kg

Manual

690 EUR

Compare amplifiers

Stomp-Head 6.CE

Taurus compact guitar amplifier ,Taurus floor guitar amplifier , Taurus floor amp , tube guitar amplifier , Taurus Stomp Head SH6, Taurus Stomp-Head SH6, Vintage guitar amplifier, StompHead 6, Taurus SH6CE, Taurus Taurus SH6.CE

Classic in a compact shape. A proposal for guitarists who prefer traditional, easy-to-use amplifiers with a sound comparable to the iconic tube giants.

The Taurus Stomp-Head 6.CE it is a fully analog design based on our own Master Tube Design technology, without any digital simulations.
The amplifier is extremely easy to use and contains everything that is necessary in a guitarist's workshop.

If you are looking for a powerful sound with the character of classic tube amplifiers, then SH-6.CE will be the right choice.

The amplifier offers three different sounds - CLEAN, CRUNCH and DRIVE. Additionally using the foot-switch gives option to activate the BOOST function which makes the signal boosted. Two separate channels with separate tone correction gives a lot opportunities to create your own, personalized sound. The sound setting process is very simple and intuitive, it works by the same way as in traditional tube amplifi.ers.

SH-6.CE can be used in various configurations

SH-6.CE can be used in various configurations:

as a classic amplifier with a speaker cabinet.There are 4 power levels to choose from: 90W, 40W, 20W and 12W.
as a preamp connected directly to the mixer or sound system using output with built-in loudspeaker simulation.

Stomp-Head 6.CE as a pre-amp.
If you want to record your guitar or use the amplifier as a pre-amp without a cabinet then you have a special tool on board - an advanced loudspeaker simulator (IR-CAB simulation). You can choose accurate simulations of two types of speakers: Celestion Vintage-30 and Celestion Creamback.
The CAB-simulation is also equipped in adjustment for microphone position. It provides additional possibilities of equalizing the colour of your sound at the line output. Thanks to this solution you can get closer to the sound conditions of a classic set of speakers with a microphone setup.
You get the right placement and sound of the instrument in the band's mix by transmitting the signal from the line output without using the speaker. All this is done in an analog way, very simple and intuitive, without the use other additional processors. The line output has two signals paths, with or without simulation. This feature also allows you to connect an external loudspeaker simulator. So you can use the built-in simulation, external simulation or both of them at once.

Taurus Custom

SH

A

how to get a great guitar sound with Taurus Servo. TUBE EMULATOR, BUFOR, SUSTAINER, COMPRESSOR, BOOSTER.

Designed by musicians for musicians