SH7 Available soon

Discover the main features

REVERB

BOOST

SERVO

NOISE GATE

Clean, Crunch & HIGH GAIN

SERVO acts as the very soul of this amplifier, enriching the tone in a magical way that players will instantly fall in love with.

The SERVO enriches the sound of instruments, adding the qualities which make playing more enjoyable and even more importantly, more inspiring. The feeling is that we are playing on much higher quality instruments than we actually are. Additionally, it makes the guitar very well set in the overall band mix. Perfectly complements the clean sound - especially enriches the sound of single coil pickups.

Good quality Reverb greatly complements guitar sound.

NOISE GATE minimizes interference that often occurs on stage and is picked up by sensitive guitar pickups, thus the overall sound is also more clear and dynamic.

The BOOST MODE allows instant increase of amp’s volume level. To control the BOOST MODE, a potentiometer and a footswitch are assigned. By tweaking the potentiometer, a desired volume can be set. Pressing the BOOST switch located on the top of the amp causes immediate access to previously set volume level. The BOOST function performs two features at the same time: it boosts a signal at the preamp's input giving extra compression and gaining the volume. The BOOST MODE is quite beneficial when a guitar solo has to be played.

The amplifier offers three different sounds - CLEAN, CRUNCH and High-Gain DRIVE. Two separate channels with separate tone correction gives a lot of opportunities to create your own, personalized sound. The sound setting process is very simple and intuitive, it works the same way as in traditional tube amplifiers.

Pedalboard Tube Guitar Amplifier

Four in one:

Analog amplifier made in Master Tube Design technologii.

The amplifier is equipped with a 4-way power output selector. It allows you to use speaker cabinets of any size, power and impedance.

The following power options are available:

7W, 30W, 60Watt

The amplifier automatically adjusts its operating parameters and can serve 4, 8 and 16 Ohm cabinets.

If you want to record your guitar or use the amplifier as a pre-amp without a cabinet then you have a special tool on board, an advanced loudspeaker simulator.

Signal from Line-out can be lead in different ways: with simulation, without simulation or both.

You can choose accurate simulations of two types of speakers:
Celestion Vintage-30 and Celestion Creamback.

A simulation of the microphone position is also available and provides additional possibilities of equalizing the colour of your sound at the line output.

Thanks to this solution you can get closer to the sound conditions of a classic set of speakers with a microphone setup. You get the right placement and sound of the instrument in the band's mix by transmitting the signal from the line output without using the speaker.

5 footswitches for immediate access to the amps five different modes:
Clean, Crunch, Drive, Boost, Mute.
Additional OUTPUTS for external controller.

Foot Controller

Clean, Crunch, Drive, Boost and Reverb.

Cabinet Simulator

2-types of speakers: Celestion Vintage-30 and Celestion Creamback.
Adjustment for microphone position.

Preamp

You can use Stomp-Head as a preamp without connection to cabinet.

Amplifier

This compact amp delivers enough loudness level for any stage size.

Basket

Buy now

Order now

Specification:

Power stage efficiency: 130Watt
Power output selector: 60W, 30W, 7W
Speakers impedance auto detection: 4,8 and 16ohm
Tubes: dual triode 6021 PHILIPS
3 channels: CLEAN, CRUNCH and HIGH-GAIN
5 footswitches: CLEAN, CRUNCH, High-Gain DRIVE, REVERB, BOOST
CHANNEL controls:
GAIN, BASS, MIDDLE, MID-RANGE switch, TREBLE, PRESENCE, VOLUME
SERVO – increases the sound saturation, adds sustain and compression
BOOST - access to set two different volume levels
REVERB
NOISE GATE
MUTE
LOW CUT -low frequency cut-off switch at the amplifier input
Serial EFFECT LOOP
CAB SIM MODULE - built-in analog speaker simulation module. Simulation is active on the line and headphone outputs.
LINE OUTPUT with Speaker Simulation. Allows send linear signal with simulation (PIN) or without simulation (RING) or both simultaneously
HEADPHONE output
AUX - input enabling connection of a signal to headphones
EXTERNAL CONTROLLER INPUTS for channel selector and BOOST
Power supply voltage range: 90-240V
Dimensions: (H x W x D) 75 x 320 x 205mm
Weight: 2,4kg

Manual

715EUR

Compare amplifiers

The SH‑10 amplifier is made for players who love classic gear with real character. A true analog amp often delivers far more satisfaction than an entire collection of digital simulations.

The Stomp‑Head SH‑10 is a fully analog design, free from any digital modeling and built on our Master Tube Design technology. Despite its exceptionally low weight and compact size, it delivers a truly massive sound.

If you’re looking for a wide palette of tones — from smooth CLEAN, through gritty CRUNCH, all the way to powerful HIGH‑GAIN — the SH‑10 will be the right tool for the job.

Stomp-Head SH-10

Pedalboard tube guitar amplifier

SH-7 can be used in various configurations:

as a classic amplifier with a speaker cabinet.
There are 4 power levels to choose from: 60W, 30W and 7W.
as a preamp connected directly to the mixer or sound system using output with built-in loudspeaker simulation.

Stomp-Head SH-10 as a pre-amp.
If you want to record your guitar or use the amplifier as a pre-amp without a cabinet then you have a special tool on board - an advanced loudspeaker simulator (IR-Cab simulation). You can choose accurate simulations of two types of speakers: Celestion Vintage-30 and Celestion Creamback. Also two types of cabinets with different dimensions - small and large can be chosen.
A simulation of the microphone position is also available and provides additional possibilities of equalizing the colour of your sound at the line output. Thanks to this solution you can get closer to the sound conditions of a classic set of speakers with a microphone setup. You get the right placement and sound of the instrument in the band's mix by transmitting the signal from the line output without using the speaker. All this is done in an analog way, very simple and intuitive, without the use other additional processors. The line output has two signals paths, with or without simulation. This feature also allows you to connect an external loudspeaker simulator. So you can use the built-in simulation, external simulation or both of them at once.

Taurus Custom

SH

A

SH

Taurus Effects Pedals Servo, Drive, Multidrive, Tux compressor, Beefmaster, MultiWay Booster

Designed by musicians for musicians